Top hydraulic seal factory manufacturer: The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart. Find extra details at rod seals.
Every other leak path within the mechanical seal is blocked with the use off a gasket, o-ring, wedge (Rubber, PTFE or Flexible Graphite). The other key aspect of a mechanical pump seal is how to maintain the seal. Springs (single or multiple), a metal bellows or just compressed elastomers are used to provide the needed energy to keep pressing the seal faces together. The load the seal faces receive are engineered into the design of the seal. The choice of what is the best depends on the temperature, and nature of what is being sealed (viscosity, abrasiveness, weight (is it a slurry?)). Cartridge Seals are pre-assembled package of mechanical seal components making installation much easier with fewer points for potential mechanical pump seal installation errors to occur. Mechanical seals occasionally require a seal pot to provide a buffer fluid for your double cartridge seals. Seal pots can not only provide a lubricating buffer, but they can also heat or cool the barrier fluid they contain.
Although construction machinery looks extremely complex, the common characteristics that can be summarized are: Usually work outdoors. The work site often changes, and some can move by themselves. The working environment is usually dusty or stained. Nowadays, construction machinery generally adopts hydraulic transmission, because hydraulic transmission has the following obvious advantages compared with mechanical transmission: The power-to-volume ratio is large and the location arrangement is easy. It can realize stepless speed change. It is easy to realize overload protection. Less shock, vibration and noise.
The rotary seal from DMS SEALS is a dynamic sealing component that is installed between the rotating shaft and the stationary parts to seal the lubricating oil and prevent external dust and debris from entering the inside of the device. When selecting the material, we fully consider the working medium, working temperature and the adaptability of the lip when the shaft rotates at high speed. It has a remarkable sealing performance and can maintain a great sealing effect for a long time.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. See even more details on https://www.dmsseals.com/.
DMS Seals is a professional hydraulic seals, industrial mechanical seals manufacturer and oil seal supplier specializing in supplying sealing solutions and various seals & o ring. As a leading custom o ring manufacturer, DMS can support OEM and ODM and can meet customers’ requests. DMS Seals adheres to the tenet of “first-class design, top manufacturing, excellent service” and strive to be an excellent supplier of sealing system solutions. DMS Seals pays the utmost attention to quality to ensure the satisfaction of our cooperative partners.